Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of steering
   2.9. Replacement of oil in the engine and an oil filter
   2.10. Check of a state and care of the battery
   2.11. Check of the cooling system
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of screenwash
   2.14. Shift of wheels
   2.15. Check of a suspension bracket and steering
   2.16. Check of the exhaust system
   2.17. Check of level of oil in the manual transmission
   2.18. Check of level of oil in the transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and lubricant of the exhaust valve
   2.23. System of catching of vapors of gasoline
   2.24. Check of system of recirculation
   2.25. Air gate of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, runner and covers of the distributor
   2.37. Check and installation of the moment of ignition
   2.38. Care of the cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Replacement of liquid in automatic transmission and the filter
   2.41. Replacement of oil in the manual transmission
   2.42. Replacement of oil in the transfer case
   2.43. Replacement of oil in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries




eeac64fe


2.9. Replacement of oil in the engine and an oil filter

GENERAL INFORMATION

Timely replacement of oil is the most effective measure applied by the owner to avoid premature wear of the engine owing to aging of oil, its fluidifying and pollution.

PERFORMANCE ORDER
1. For ensuring access to the lower part of the car, the last needs to be established on two supports with a cross-piece, either to lift a telfer, or to come around on a hole or a platform.
2. Find a drain stopper of the pallet of the engine.
3. Install the car on the horizontal platform. Warm up the engine, stop and turn off a stopper of a maslozalivny mouth on a cover of a head of cylinders.
4. Lift the car and establish on supports.
5. Carefully, trying not to concern hot details of the exhaust system, substitute the pallet and turn off a stopper.
6. Merge oil, check existence in the merged oil of metal shavings and sawdust.
7. After running off of oil wipe a stopper with pure rags.
8. Wipe the pallet about a drain opening and carefully tighten a stopper.
9. Substitute the pallet under an oil filter.
10. Remove all tools from under the car and lower the car.
11. By means of a special key turn off an oil filter (it is specified by an arrow) (to rotate counterclockwise) then turn out the filter hands.
12. Carefully clear the place of a prileganiye of consolidation of the filter on the block of cylinders.
13. Make sure that the type and the sizes of the new filter completely coincide with type and the sizes of fulfilled. Slightly oil rubber laying of the new filter for the engine and wrap the filter into place.
14. Wrap the filter before contact of laying with the surface of the block of cylinders, tighten the filter, having turned on 3/4 turns.
15. Fill in about 3 l of oil, having a little waited, check oil level. If level normal, then wrap a stopper of a mouth and tighten by hand. Start the engine that oil filled all lubricant channels.
16. On the working engine check tightness of a stopper of the pallet and filter, having tracked these places within a minute. At emergence of a leak stop the engine and tighten a stopper or the filter.
17. Stop the engine and wait several minutes that oil flew down in the pallet. Again check oil level on the probe. If necessary add oil to the top mark in the probe.

18. In we lie several trips after change of oil in the engine you watch a leak and check oil level.