Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of steering
   2.9. Replacement of oil in the engine and an oil filter
   2.10. Check of a state and care of the battery
   2.11. Check of the cooling system
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of screenwash
   2.14. Shift of wheels
   2.15. Check of a suspension bracket and steering
   2.16. Check of the exhaust system
   2.17. Check of level of oil in the manual transmission
   2.18. Check of level of oil in the transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and lubricant of the exhaust valve
   2.23. System of catching of vapors of gasoline
   2.24. Check of system of recirculation
   2.25. Air gate of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, runner and covers of the distributor
   2.37. Check and installation of the moment of ignition
   2.38. Care of the cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Replacement of liquid in automatic transmission and the filter
   2.41. Replacement of oil in the manual transmission
   2.42. Replacement of oil in the transfer case
   2.43. Replacement of oil in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries



2.36. High-voltage wires, runner and covers of the distributor

GENERAL INFORMATION

Characteristic defects of a cover of the distributor

1. Cracks on a wire conclusion

2. Cover cracks

3. Breakdown

4. Erosion of electrodes

5. Wear of a piece of coal

Check and replacement

PERFORMANCE ORDER
1. High-voltage wires of spark plugs should be checked (and if necessary to change) along with replacement of candles.
2. The simplest way of check consists in survey of wires on the working engine in the darkened garage. At detection of a luminescence (breakdown) of a wire replace. Check a condition of a cover and the runner of the distributor.
3. For check and cleaning of wires disconnect each wire separately. On cars of late releases it is required to remove a slip on a cover of a head of cylinders. Disconnect a wire on a distributor cover. Check a condition of contacts of wires and sealants. Wipe wires. Strongly do not bend a wire as the conducting vein can break. At detection of cracks, traces of breakdown and a podgoraniye of a wire replace.
4. Check existence of corrosion on sockets of tips of wires (on both sides) and conclusions of candles. Check durability of demountable connection, having dressed a tip of a wire on a candle and having shaken it. At leaky connection draw in contact petals.
5. Unscrew screws of fastening and uncover the ignition distributor. Wipe a cover absolutely and check existence in and outside of a cover of cracks, traces of superficial breakdown (the thin charred paths), wear, a podgoraniye and weakening of contacts (see rice. Characteristic defects of a cover of the distributor).
6. Remove the runner (a photo at the left) and examine in the places specified by shooters a photo on the right.
7. If the old cover is established, then check resistance between a conclusion of a cover and a candle. If resistance exceeds norm, then replace a cover and a wire. Change each wire separately.