Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of steering
   2.9. Replacement of oil in the engine and an oil filter
   2.10. Check of a state and care of the battery
   2.11. Check of the cooling system
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of screenwash
   2.14. Shift of wheels
   2.15. Check of a suspension bracket and steering
   2.16. Check of the exhaust system
   2.17. Check of level of oil in the manual transmission
   2.18. Check of level of oil in the transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and lubricant of the exhaust valve
   2.23. System of catching of vapors of gasoline
   2.24. Check of system of recirculation
   2.25. Air gate of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, runner and covers of the distributor
   2.37. Check and installation of the moment of ignition
   2.38. Care of the cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Replacement of liquid in automatic transmission and the filter
   2.41. Replacement of oil in the manual transmission
   2.42. Replacement of oil in the transfer case
   2.43. Replacement of oil in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries




eeac64fe


2.39. Naves and bearings of forward wheels

Check and replacement of lubricant

PERFORMANCE ORDER
1. Bearings of forward wheels should be checked rocking of a wheel at each raising of a front.
2. At detection of a side play when rocking in the vertical plane it is necessary to sort knot and to check a condition of bearings.
3. Remove a wheel.
4. Remove a support, take aside and record.
5. Remove the mechanism of blocking of naves (see subsection 7.4.3.4).
6. An external nut also turn off Raskontrite.
7. Remove a washer, turn off an internal nut.
8. Remove a persistent washer.
9. Give a nave on yourself and back, get the external bearing.
10. Remove a nave.
11. Get an epiploon.
12. Remove the internal bearing.
13. Carefully wash out a nave and bearings solvent and dry.
14. Examine bearings and external holders. At detection of damages replace the bearing for what beat out a holder to brass small beards and press new.
15. Put refractory lubricant in the bearing.
16. Grease with a thin layer of a neck of a nave, internal surfaces of holders of bearings, epiploons and boring under an epiploon.
17. Put lubricant in a nave cavity between external holders, having formed a finger a lubricant fillet at the edges of holders.
18. Install the internal bearing in a nave and cover with lubricant a bearing end face.
19. Press an epiploon aflush with a nave surface.

Adjustment

PERFORMANCE ORDER
1. Establish a nave and the external bearing.
2. Dress a washer and wrap an internal nut with m 51 N.'s moment, at the same time turning a nave.
3. Release a nut and again tighten with the moment 4,8 N. of m, at the same time turning a nave. Make sure that the side play is absent, and the wheel rotates freely.
4. Dress a lock washer and tighten an external nut with m 56 N.' moment. Check a side play, in the presence of a side play you perezatyanit an internal nut. Bend kontrovochny ledges of a washer in opposite directions.
5. Further assembly is conducted upside-down. Slightly grease litoly knot of blocking of a nave (excess of lubricant is not allowed).