Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car

Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
- 11. Electric equipment
   11.1. Search of malfunctions
   11.2. Safety locks
   11.3. Fusible crossing points
   11.4. Breakers
   11.5. Relay
   11.6. Breaker of indexes of turn / alarm system
   11.7. A combination of switches on a steering column
   11.8. Lock of ignition and drum of the lock
   11.9. Indexes of level of fuel, pressure and temperature of oil
   11:10. Guard of devices
   11:11. Screen wiper electric motor
   11:12. Receiver and loudspeakers
   11:13. Antenna
   11:14. Heater of back glass
   11:15. Headlights
   11:16. Case of a halogen headlight
   11:17. Sound signal
   11:18. Replacement of lamps
   11:19. Side mirrors with the electric drive
   11:20. System cruise control
   11:21. Window regulator electric drive
   11:22. Electric drive of door locks
   11:23. Safety cushions
+ 12. Electrical circuitries

autotechmobilemechanic

11:15. Headlights

GENERAL INFORMATION

Screws for adjustment of a bunch of a halogen lamp

1. A bolt And for horizontal adjustment
2. A bolt With for vertical adjustment
3. A bolt In for horizontal adjustment

4. Level of horizontal adjustment
5. Level of vertical adjustment

Screen marking for adjustment of a beam of light of headlights

1. The line at distance from a floor to the center of headlights

2. Area of a light spot

3. The line at distance from an axis of symmetry of the car to the center of headlights

4. Axis of symmetry of the car

5. Distance of 7,5 m

6. Forward plane of a headlight

Removal and installation

PERFORMANCE ORDER

1. Disconnect the battery from weight.
Headlights with a non-demountable optical element
	2. Remove facing of a headlight. On the FJ62 cars remove a plafond of the index of turn.
3. At removal of a headlight it is forbidden to rotate the sprung screws of adjustment of a bunch.
	4. Unscrew screws of fastening of a frame and remove a frame of an optical element, holding a headlight.
	5. Give a headlight outside and disconnect the socket. Remove a headlight.
6. Attach the socket, having oriented a new element so that the cast figures on a lens were turned up.
7. Establish a frame, tighten screws, insert a spring.
8. Check adjustment of a bunch (if the adjusting screw rotated).
Halogen headlights
Prevention Halogen lamps gas-filled, under pressure. It is forbidden to undertake a lamp cylinder. Wipe the polluted lamp with the pure napkin moistened with alcohol.
9. Disconnect the socket from the headlight back.
	10. Turn the holder counterclockwise and get from the case.
11. Pull a lamp and get from the holder. Insert a new lamp, without concerning a cylinder.
12. Attach the socket and check work of a headlight.

Adjustment

Prevention

It is necessary to check adjustment of headlights each 12 months, when replacing a headlight or after repair of a forward part of a body. It should be noted that the described procedure allows to adjust only approximately headlights, exact adjustment is carried out in car service.

PERFORMANCE ORDER

	1. On the headlight case with a non-demountable optical element 2 sprung screws for adjustment in vertical (from above) and horizontal (sideways) the planes are provided.
2. Adjustment of a halogen headlight is provided with screws on the case (see rice. Screws for adjustment of a bunch of a halogen lamp). Rotation of screws regulates the central provision of the index of the level located in the top part of a headlight.
3. The simplest way of adjustment consists in installation of a bunch on a marking on the screen (wall).
4. Designate a tape of a cross hairs symmetrically a car axis (see rice. A screen marking for adjustment of a beam of light of headlights). For more exact marking drive up to a wall on distance about 20 cm.
5. Install the car in 7,5 m from a wall.
6. Adjustment is carried out at normal loading of the car and a thin tank. Establish a bunch of passing beam of headlights so that the light spot settled down 5 cm below than a horizontal and verticals are 5 cm more right. For raising of a bunch rotate the screw clockwise and vice versa. The same concerns adjustment to the left-to the right.
7. Turn on driving beam of headlights and adjust a bunch so that the spot was strictly on the vertical line, directly under a horizontal.
Prevention To precisely expose bunches of driving and passing beam in such a way it can be impossible. In this case try to adjust more precisely passing beam with which it is necessary to go more often and on which traffic safety more depends.
8. As soon as possible adjust headlights in car service.