Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   - 3.2. Verkhneklapanny engine 1FZ-FE
      3.2.1. Technical characteristics
      3.2.2. Types of repair without dismantle of the engine
      3.2.3. Cover of a head of cylinders
      3.2.4. The soaking-up collector
      3.2.5. Final collector
      3.2.6. Cam-shafts and pushers
      3.2.7. Head of cylinders
      3.2.8. Cover of the chain drive of cam-shafts
      3.2.9. Forward epiploon of the crankshaft
      3.2.10. Oil pallet
      3.2.11. Oil pump
      3.2.12. Flywheel (drive plate of the hydrotransformer)
      3.2.13. Back epiploon of the crankshaft
      3.2.14. Details of a suspension bracket and engine
   + 3.3. Dismantle and capital repairs of the engine
   + 3.4. Engine electric equipment
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries




eeac64fe


3.2.13. Back epiploon of the crankshaft

Replacement

PERFORMANCE ORDER
1. Remove the check point (transmission). Remove a back plate.
2. The epiploon can be removed without dismantle of the oil pallet or removal of the holder of an epiploon. However, such way is not recommended as the epiploon is established in the holder with a big tightness and therefore it is possible to damage an epiploon or in the holder, or at installation. If you nevertheless want to try, then the screw-driver take an old epiploon.
3. Grease a neck of the crankshaft and working edges of a new epiploon with universal jellied lubricant and carefully establish an epiploon into place. A working edge of an epiploon very rigid therefore at installation on the crankshaft push an epiploon carefully, working with a smooth subject. Easy blows press an epiploon into place. You do not strike sharp blows, otherwise the epiploon can be damaged.
4. It is recommended to apply a method which is described below. However, here it will be required to open consolidation in a back part of the pallet and to remove the holder of an epiploon.
5. Turn off two extreme back bolts of the pallet which are screwed in the holder. Open by the pallet consolidation between a back part of the pallet and the holder of an epiploon.
6. Turn off bolts, remove the holder and remove the laying remains. Remove consolidation from the demountable plane of the pallet.
Prevention

Close an open part of the pallet pure rags that the consolidation remains did not get during fastening of the pallet at assembly.


7. Having put to the holder with an epiploon on two wooden whetstones, beat out an epiploon the screw-driver from a reverse side.
8. Press in the holder a new epiploon blows of the hammer through a wooden pro-rate.
9. Grease working edges of a new epiploon and a neck of the crankshaft with universal jellied lubricant. Install new laying of the holder of an epiploon on the block of cylinders. On the opened part of the maslyanyy pallet apply the RTV sealant roller, especially on the plane adjacent to the block of cylinders.
10. Carefully dress an epiploon with the holder on a crankshaft neck.
11. Tighten the holder's bolts with the set moment.
12. Further assembly is carried out upside-down.