Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
- 10. Body
   10.1. Maintenance and repair
   10.2. Vinyl finishing
   10.3. Upholstery and rugs
   10.4. Repair of insignificant damages
   10.5. Repair of considerable damages
   10.6. Loops and locks
   10.7. Windshield and motionless glasses
   10.8. Cowl
   10.9. Latch of a cowl and cable of the drive
   10:10. Forward lattice
   10:11. Forward wing
   10:12. Internal panel of a door
   10:13. Door lock, switch of the lock and handle
   10:14. Door glass
   10:15. Window regulator
   10:16. Side mirrors
   10:17. Door
   10:18. Door of a back compartment
   10:19. Back cover (top door of a back compartment)
   10:20. Casing of a steering column
   10:21. Panels of forward facing of salon
   10:22. Average floor section
   10:23. Forward facing panel of salon
   10:24. Seats
   10:25. Bumpers
+ 11. Electric equipment
+ 12. Electrical circuitries



10:17. Door

GENERAL INFORMATION

Prevention

Works are performed together.


Removal and installation

PERFORMANCE ORDER
1. Lift glass. Disconnect the battery from weight.
2. Open a door and establish wooden props under a door, having covered them with rags.
3. Remove the internal panel of a door and the water filter.
4. Disconnect all sockets of conducting, a wire on the weight and latches, the fixing conducting plaits. Previously designate all sockets and wires.
5. Disconnect a rubber casing from a door. Then stretch conducting through an opening in a casing, having removed with that of a door.
6. Carefully beat out an axis of the limiter of opening of a door in the direction specified by an arrow.
7. Outline contours of door loops.
8. Holding a door, turn off bolts of loops using a special key for an otvorachivaniye of bolts of door loops and remove a door.
9. Installation is carried out upside-down.

Adjustment

Adjustment of provision of a clamp of the lock

For adjustment lower screws and move a lock clamp in the necessary direction.

PERFORMANCE ORDER
1. Before adjustment check existence of a side play in axes of door loops. Completely open a door and shake a door up-down, without shaking at the same time a body. If the side play of loops exceeds 1,6 mm, then loops should be replaced.
2. Adjustment of a door concerning a body is reached by movement of a door at the released bolts of fastening of loops to a body or to a door. Doors are considered adjusted if the top edge of a door is parallel to a body roof edge, the surface of a forward door settles down aflush with a wing, a surface of a back door – aflush with a back wing, and the lower edges of doors coincide with a powder profile. If adjustment of doors is not reached by movement in loops, then between loops and a body (door) it is necessary to lay remote laying (are available on sale).
3. Remove the internal panel of a door and the water filter.
4. For adjustment of provision of the closed door outline a contour of a clamp and be convinced that the latch of the lock makes contact with the central part of a clamp. Otherwise adjust, moving a clamp up-down.
5. For adjustment of a clamp be convinced of the side direction that the door is aflush with the next panels of a body (a forward or back wing). Otherwise move a clamp in the horizontal direction so that the door was aflush with the next panels of a body and was freely locked.