Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   - 3.2. Verkhneklapanny engine 1FZ-FE
      3.2.1. Technical characteristics
      3.2.2. Types of repair without dismantle of the engine
      3.2.3. Cover of a head of cylinders
      3.2.4. The soaking-up collector
      3.2.5. Final collector
      3.2.6. Cam-shafts and pushers
      3.2.7. Head of cylinders
      3.2.8. Cover of the chain drive of cam-shafts
      3.2.9. Forward epiploon of the crankshaft
      3.2.10. Oil pallet
      3.2.11. Oil pump
      3.2.12. Flywheel (drive plate of the hydrotransformer)
      3.2.13. Back epiploon of the crankshaft
      3.2.14. Details of a suspension bracket and engine
   + 3.3. Dismantle and capital repairs of the engine
   + 3.4. Engine electric equipment
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries




eeac64fe


3.2.8. Cover of the chain drive of cam-shafts

GENERAL INFORMATION

Details of a forward part of the engine

1. Compressor
2. Arm
3. Pallet 1
4. Oil level sensor
5, 7. Laying
6. Pallet 2
8. Lower guard
9. Roller of a natyazhitel
10. Pulley
11. Adjusting level of a belt
12. Ring
13. Forward epiploon
14. Radiator branch pipe
15. Cover
16. Uspokoitel
17. Gear wheel of the drive of the oil pump
18. Leading asterisk
19. Drive gear wheel
20. Oil nozzle
21. Boot of a natyazhitel
22. Chain
23. The conducted cam-shaft gear wheel

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Block back wheels.
3. Lift a car front.
4. Remove the lower guards.
5. Remove a broad tank of a radiator (see subsection 4.5).
6. Turn out candles and take off all belts of the drive.

7. Remove the compressor of the conditioner and take aside, without disconnecting from the highway (bolts of the compressor of the conditioner are specified by shooters).
8. Shoot the generator, a video of a natyazhitel and all arms (bolts of an adjusting arm of the generator are specified by shooters).
9. Remove the drive a cruise control (if it is provided) and take aside.
10. Disconnect the lower hose of a radiator and remove the pump of cooling liquid.
11. Install the piston of the 1st cylinder in compression step VMT.
12. Remove a head of cylinders.
13. Remove the pallet.
14. Turn off a bolt having recorded a crankshaft pulley.
15. Remove a crankshaft pulley a stripper.
16. Turn off bolts and nuts of a cover of a chain and carefully uncover.
17. Remove a chain and an asterisk. Remove uspokoitel and details of a natyazhitel.

Check

PERFORMANCE ORDER
1. Check a condition of teeths of a gear wheel of a cam-shaft. Check a condition of a chain, wear of rollers and connecting links. Replace worn-out details. In case of strong wear of uspokoitel remove and clear the pallet and an oil receiver.
2. Check work of a plunger and clamp of a natyazhitel. The plunger has to move freely in a case opening (at the left). The clamp has to hold reliably a plunger (on the right).
3. Check purity of a jet of an oil nozzle.

Installation

Designation of the bolts of fastening of a cover of a chain differing in the sizes

Bolt And – 30 mm

Bolt In – 50 mm

Bolt With – 60 mm


PERFORMANCE ORDER

1. Clear a forward part of the engine, a chain and a cover, establish new sealing rings and a nozzle. The nozzle has to be turned towards a chain.
2. Dress a chain on a cam-shaft asterisk, having combined tags, press out a chain with uspokoitel, having tied up a strong tape.
3. Combine other link with a distinctive tag with a groove under a spline of the crankshaft (arrow) and dress on the leading asterisk.
4. Apply on a cover 3 mm – the sealant roller, be convinced available all laying and establish a cover (within no more than 5 min. after drawing), having entered the roller of the leading rotor of the oil pump into gearing with the leading gear wheel of the crankshaft.
5. Wrap bolts (see rice. Designation of the bolts of fastening of a cover of a chain differing in the sizes) also tighten with the set moment. Remove a chain binding.
6. Establish other details upside-down. Start the engine, only after check of correctness of installation of a chain.