Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car


Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   - 3.2. Verkhneklapanny engine 1FZ-FE
      3.2.1. Technical characteristics
      3.2.2. Types of repair without dismantle of the engine
      3.2.3. Cover of a head of cylinders
      3.2.4. The soaking-up collector
      3.2.5. Final collector
      3.2.6. Cam-shafts and pushers
      3.2.7. Head of cylinders
      3.2.8. Cover of the chain drive of cam-shafts
      3.2.9. Forward epiploon of the crankshaft
      3.2.10. Oil pallet
      3.2.11. Oil pump
      3.2.12. Flywheel (drive plate of the hydrotransformer)
      3.2.13. Back epiploon of the crankshaft
      3.2.14. Details of a suspension bracket and engine
   + 3.3. Dismantle and capital repairs of the engine
   + 3.4. Engine electric equipment
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries




eeac64fe

3.2.10. Oil pallet

 Removal
PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Put the car on the emergency brake and block back wheels.
3. Lift a car front.
4. Remove mud guards of the engine.
5. Merge oil and remove an oil filter. Remove an oil indicator.
6. Remove the stabilizer of a forward suspension bracket (see subsection 9.2).
7. Remove exhaust pipes assembled.
8. Remove the sensor of level of oil and examine.
9. Turn off pallet 2 bolts (the lower section).
10. Carefully separate and remove the lower section.
11. Turn off bolts (are specified by shooters a photo at the left) and nuts near a pulley (are specified by shooters a photo on the right) the pallet 1 (the top section).
12. Open consolidation and carefully separate the top section.
13. Incline and remove the top section.
14. Turn off nuts of fastening of an oil receiver (are specified by shooters).
15. Turn off nuts of maslootrazhatel (are specified by shooters) and remove an oil receiver.

Installation

PERFORMANCE ORDER
1. Remove the consolidation remains from the demountable planes of the block of cylinders and the pallet. Wash out the condensed planes solvent.
2. Be convinced of purity of carving openings in the block of cylinders.
3. Check existence on the demountable plane of the pallet of deformations, especially about openings under bolts. If necessary align the plane the hammer on a board.
4. Check a condition of an oil receiver, existence on it of cracks and a contamination of the filter of rough cleaning. Establish an oil receiver tube.
5. Check a condition of the sensor of level of oil and the socket. Replace laying.
6. At assembly establish new laying of an oil receiver in a forward cover.
7. Apply 3 mm rollers of sealant on the condensed pallet 1 plane.
Prevention

The detail has to be established no later than 5 minutes after putting sealant.
8. Carefully install the pallet and wrap bolts. In three-four receptions tighten pallet bolts with the set moment, beginning an inhaling in the central part.
9. Apply 3 mm rollers of sealant on the pallet 2 plane, install the pallet, evenly and gradually tighten bolts with the set moment.
10. Further assembly are carried out upside-down. Fill in oil in the engine and replace the filter. Replace laying of an exhaust pipe of the muffler.
11. Start the engine and be convinced of lack of a leak.