Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and operation of the car



Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of steering
   2.9. Replacement of oil in the engine and an oil filter
   2.10. Check of a state and care of the battery
   2.11. Check of the cooling system
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of screenwash
   2.14. Shift of wheels
   2.15. Check of a suspension bracket and steering
   2.16. Check of the exhaust system
   2.17. Check of level of oil in the manual transmission
   2.18. Check of level of oil in the transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and lubricant of the exhaust valve
   2.23. System of catching of vapors of gasoline
   2.24. Check of system of recirculation
   2.25. Air gate of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, runner and covers of the distributor
   2.37. Check and installation of the moment of ignition
   2.38. Care of the cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Replacement of liquid in automatic transmission and the filter
   2.41. Replacement of oil in the manual transmission
   2.42. Replacement of oil in the transfer case
   2.43. Replacement of oil in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries




eeac64fe


2.31. Drive belts

GENERAL INFORMATION

Characteristic signs of wear of a wedge-shaped belt

1. Furrows on each side

2. Carbonization

3. Cracking

4. Peeling from a basis

5. Wipe (brightness)

6. Oil hit

7. Anguish

Check of a tension of a belt

1. Ruler

2. Whetstone

3. Deflection

On engines wedge-shaped belts of the drive are applied. Because of constant loadings there is a pulling of belts over time and the state them worsens. Therefore, belts should be checked periodically.

The quantity of the belts established on the car depends on type of the engine and on a car complete set. Belts are used for the drive of the generator, the pump of cooling liquid, the conditioner and the hydraulic booster.

Check

PERFORMANCE ORDER
1. Stop the engine and, having opened a cowl, find drive belts. Check a condition of belts, existence of characteristic signs of wear, having lit them with a small lamp. Check a condition of belts on both sides.
2. Check a belt tension in deflection size in the middle between pulleys (see rice. Check of a tension of a belt). If distance between centers of pulleys of 180-300 mm the deflection has to be 6,5 mm, and at distance between centers of 300-400 mm the deflection has to be 13 mm for maple belts and 6,5 mm for belts with a ridge profile. The ruler has to be a perependikulyarna to whetstone.

Adjustment of a tension

PERFORMANCE ORDER
1. On all cars for adjustment of a tension of a belt of the drive it is necessary to move the unit on an arm.
2. The belt is regulated by two bolts – axial (And) and adjusting (In). For adjustment weaken a bolt And yes rotate a bolt In to displace a roller or a pulley of mobile knot, having pulled or having weakened a belt.
3. After adjustment check a belt tension, if necessary again weaken bolts and adjust a tension. Upon termination of adjustment tighten bolts.
4. On cars of early releases a mobile roller of a natyazhitel with an adjusting bolt are absent, a roller (or a pulley) are displaced by the auxiliary lever (mount).

Replacement
PERFORMANCE ORDER
1. For replacement of a belt perform the same preliminary procedures, as for adjustment then take off a belt. All belts are recommended to be changed at the same time. Before removal designate each belt and the corresponding pulley.
2. At acquisition compare a new belt with replaced.
3. Adjust a belt tension.